Custom EPE foam machine suppliers for factory

Heat treatment is to improve the mechanical properties of the material, eliminate the residual stress and improve the machinability of the metal. According to the different purposes of heat treatment, heat treatment process can be divided into two categories: preparation heat treatment and final heat treatment.1, prepare heat treatmentThe purpose of the prepara heat treatment is to improve the processing performance, eliminate the internal stress and prepare the metallographic structure for the final heat treatment. The heat treatment processes are annealing, normalizing, aging, quenching and tempering, etc.(1) aging treatment is mainly used to eliminate the internal stress produced in the manufacturing and machining of hydraulic die cutting machine. In order to avoid too much transport work, for the general accuracy of the parts, in the finishing process before the arrangement of A. However, high precision parts, should be arranged two or several aging treatment process. Simple parts can not be generally aging treatment. In addition to casting, precision parts for some low rigidity, in order to eliminate the internal stress generated during machining, stable machining precision, often arranged several times in the aging treatment between roughing semi finishing. Some shaft parts processing, straightening process should be arranged after aging treatment.(2) the annealing and normalizing annealing and normalizing of the vertical cutting machine for the blank after heat treatment. Carbon steel and alloy steel carbon content more than 0.5%, in order to reduce the hardness of easy cutting, often by annealing treatment; carbon content less than 0.5% carbon steel and alloy steel, in order to avoid the low hardness of cutting and sticking knife by normalizing treatment. Annealing and normalizing can refine grain and uniform structure, and prepare for later heat treatment. Annealing and normalizing are often arranged prior to rough machining and rough machining.(3) and high temperature tempering is tempering after quenching, it can obtain uniform tempered sorbite structure to reduce deformation of surface quenching and nitriding treatment for the future, it can also be used for pre heat treatment tempering.Due to the excellent mechanical properties of the parts after quenching and tempering, the parts with high hardness and wear resistance are not required, and can also be used as the final heat treatment process.2, the final heat treatmentThe purpose of the final heat treatment is to improve the mechanical properties such as hardness, wear resistance and strength.(1) carburizing carburizing and quenching for low carbon steel and low alloy steel, improve the carbon content of the surface, after quenching to obtain high surface hardness, but the heart still keep a certain strength and toughness and plasticity. Carburizing and carburizing. Local carburizing to non carburizing part of the measures to be taken to prevent seepage (copper plated or impermeable material). Due to the large deformation of carburizing and quenching, and the carburizing depth is generally between 0.5~ 2mm, so the carburizing process is generally arranged in the semi finishing and finishing. The technological process is as follows: cutting forging, normalizing, roughing, semi finishing, carburizing, quenching and finishing.When the carburizing parts of the local carburizing parts are used to increase the allowance, the process of removing the excess carburized layer shall be arranged after carburizing.(2) quenching with surface quenching and quenching. The surface quenching is widely used because of the deformation, oxidation and decarburization, and the surface quenching has the advantages of high external strength, good wear resistance, and good toughness and impact resistance. In order to improve the mechanical properties of surface hardened parts, heat treatment, such as quenching and tempering, normalizing, and so on, should be used as the initial heat treatment. The general technological route is as follows: blanking, forging, normalizing, annealing, rough machining, quenching and tempering, semi finishing, surface hardening, finishing.(3) nitriding is a method of treating nitrogen atoms to penetrate a metal surface to obtain a layer of nitrogen containing compounds. Nitriding layer can improve the surface hardness, wear resistance, fatigue strength and corrosion resistance. Because of the low temperature nitriding treatment, small deformation, and the nitriding layer is thin (less than 0.6~ 0.7mm), should be arranged after nitriding process, to reduce deformation of nitriding, the cutting should be eliminated after high temperature tempering stress.

The vertical cutting machine is a small die-cutting machine that is manually operated and is suitable for cutting products with small specifications. Because the size of the cut die is different and the thickness of the material is not the same, the pressure required is not complete. The following describes how the rocker can adjust the pressure. There are two main ways:1、Under normal circumstances, fine-tune the machine pressure by the knob on the swing arm headAdjustment knob: When the knob is adjusted to the minimum, the pressure is minimum; when the knob is adjusted to the maximum, the pressure is maximum2、Adjust the hydraulic valve inside the cutting machineStep 1、 Adjust the screw pointed and adjust the pressure to the left and right.Step 2、After adjusting to the applicable pressure, tighten the screw pointedSetting of cutter height of cutting machine1, remove the debris on the working surface of the board, will be placed in the center of the plastic mold;2, the machine starts, will set the handwheel release, the pressure system to zero;3, set the switch to the right to the "knife mold set" direction, cutting plate 13 that began to slow down to close the knife die will automatically stop;4. Set the handwheel to the bottom and tighten it. Set the switch system (left) to the "cut" position before starting 04;5, and then press the brake switch, the cutting plate on the immediate recovery to the highest position, at this time the knife mold set is completed.Adjustment of precision eva foam cutting machine1, setting of the knife mold work is completed, will be laid on the material on the plate, then put in the knife mold materials, and then promote the feed plate cutting area; 2, respectively, with both hands pressed 12 cutting switch, at this time decreased pressure on the cutting platen die cutter, cutter to cut off the material automatically after back to the position before starting to stop;3, in the blanking material, such as material found not completely cutting when the cutting depth of 03 to adjust the controller, the "pressure system" to counter clockwise direction of rotation; such as knife rubber molded into too deep, will be "pressure system" to the counter clockwise rotation, adjustment of the longer the cutting depth is deeper, try to to adjust the cutter slightly pressed into the sheet so far;4, the material will be pulled out of the cutting area, take out the material, in order to complete a blanking process.

This automatic cutting eva foam cutting machine suitable for continuous punching of various non-metallic roll materials with a width of <1600mm , such as leather、cloth、EVA、Sponge etc.Automatic cutting machine operation safety instructions：Just same as other cutting machines, there’s the danger for the operator to operate the Machine. If you could strictly abide by the safety instructions, the danger could be avoided as much as possible.The Machine is designed for the special purpose. It’s strictly forbidden to be used for other purpose or be transformed. For any question, please continue to operate only after completely understanding the status or consulting us.1、Read the Manual carefully and well understand the operating procedures and the main points of the Machine. In addition, it’s also necessary to know about the working procedure of the Machine and the relative dangers.2、The Machine should be with the reliable grounding.Only the worker with the related qualifications could have the grounding work for the Machine.3、It’s not allowed to tear down any accessories or protective device.4、The working site should be clean and neat. It’s not allowed to place the Machine where is open or damp. In addition, the site should be with enough light.5、The vertical cutting machine should be operated by the appointed operator. The operator should be elder than 18 years old, and have the training accordingly.Children is strictly forbidden to close to the working site. Any visitors not relative to the operation should keep the safe distance.6、The operation of the Machine should strictly refer to the technical parameters displayed on the nameplate.7、Only one operator could operate the Machine at the same time.8、The uniform for the operation should fits well. It’s not allowed to have gloves or decorations. The operator with long hair should have the hood.9、The power supply should be cut down for maintenance.Please make sure that the power supply is cut down and that the motor has stopped running completely before have the maintenance and repairing for the hydraulic die cutting machine. In addition, it’s necessary to hang the warning sign.For maintaining or repairing the motor or the hydraulic system, it should be done only after the motor and the hydraulic oil completely cools down. 10、The parts and accessories for placement could be purchased from us.11、Please check the parts of the vertical foam cutting machine before startup.12、Please leave only after the power supply is cut off and the Machine stops completely.It’s strictly forbidden for the operator to leave the running Machine.13、It’s strictly to cut any material with explosion danger, or to use the Machine in the dangerous conditions.14、The operator should be clear-headed when working.It’s strictly forbidden for the operator to work after drinking, taking medicine, having drugs or being tired.15、We would not undertake any responsibilities for any lost resulted from:a. appropriate operationb. incorrect maintenancec. incorrect operationAnything caused by the loss, the company shall not bear the responsibility.

Use of cutting machineIn industrial production, form cutting machines are used in a wide range of applications.Its function is mainly to use the forming die to obtain the desired sheet or semi-finished product by punching action.The cutting machine is widely used and can be cut into non-metallic materials, such as the industry: for mats, plastics, leather, automotive interiors, electronics, pearl cotton, sponges, eva, rubber, automotive interiors, floor mats, fabrics, Parts, cloth, mask, underwear, foam, etc. Bubble industry: Suitable for leather, fabrics, parts, automotive interiors, fabrics, pearl cotton, sponges, floor mats, floor mats, plastics, parts, sponges, eva, electronics, leather, masks, foams, etc.Widely used in: leather processing industry, footwear industry, leather goods industry, handbag industry, garment industry, glove industry, hat industry, toy industry, stationery industry, plastics industry, pearl cotton industry, sponge industry, carpet industry, plastic industry, Silk industry, handicraft industry, hanging industry, embroidery industry, paper industry, jigsaw and model industry, sports equipment industry, electronics industry, automobile industry and other light industry.how to seting die cutter(1) When setting the cutter, be sure to loosen the setting handwheel so that the setting lever touches the cutting point control switch. Otherwise, the setting operation cannot be generated when the cutter setting switch is turned ON.(2) When working, the cutting knife should be placed in the center position of the upper pressing plate as much as possible to avoid the unilateral wear of the machine and affect its life.(3) Replace the new cutter. If the height is not the same, please reset it according to the setting method. Precision four column cutting machine.(4) When the automatic cutting machine is in motion, please leave the cutting knife or the seesaw. It is strictly forbidden to use the hand to help the cutting die to cut it to avoid danger.(5) If the operator needs to leave the position temporarily, please turn off the motor switch to avoid damage to the machine by improper operation.(6) Please avoid overloading to avoid damage to the machine and reduce the service life.Two-column cutting machine vs the four-column cutting machine1.The two-column cutting machine is the hydraulic plane cutting machine. The four-column cutting machine is the precision four-column cutting machine that we usually hear.2.The hydraulic plane cutting machine is earlier than the four-column cutting machine. hydraulic plane cutting machine  first, followed is four-column cutting machine.3.At present, there are many four-column cutting machines on the market. Four-column cutting machine more expensive than hydraulic plane cutting machine,Almost all manufacturers do not produce hydraulic plane cutting machine,Because of the low price and small profit margin. 60% product are export for Veinas Machinery, so the hydraulic plane cutting machine and four-column cutting has been sold a lot.4.The pressure of the two-column plane cutting machine will not exceed 30 tons,The pressure of the four-column cutting machine is currently more than 500 tons of Veinas Machinery.More information about foam automatic cutting machines can pay attention to Veinas Machinery, Veinas Machinery has more than 10 years of production experience.